HOME > LED Products Category > Capacitor Manufacturer > Multilayer Ceramic Capacitors > Description Of MA Series > Environment

ENVIRONMENTAL

Test
Test Conditions
Post-Test Inspection Requirements
Solderability
IEC 384-10 4.11 / JIS C 5102 8.13
Solder 60 Sn/40 Pb, 235 ± 5oC Immersed
for 5 secs.
At least 75% of termination area should be well tinned.
No visible damage

*1

Resistance to
Soldering Heat

IEC 384-10 4.10 / JIS C 5102 8.14
Immersed in solder bath at
260 ± 5oC for 10 ± 1 secs.
Recovery :6 ~ 24 hrs. (COG)
24 ± 2 hrs. (X7R, Z5U, Y5V)
At least 75% of termination should be covered by solder.
No visible damage
 
COG(1BCG)
X7R(2R1)
Z5U(2E6)
Y5V(2F4)
£GC/C
£±0.5%, or ±0.5pF
whichever is greater
£+10%
-5%
£+20%
-10%
£+20%
-10%

*2

Rapid Change of
Temperature

IEC 384-10 4.12 / JIS C 5102 9.3
-55oC to + 125oC, 5 cycles (COG, X7R)
Duration : 30 mins.
Recovery :6~24 hrs. (COG)
24 ± 2 hrs. (X7R)
No visible damage
 
COG(1BCG)
X7R(2R1)
£GC/C
£±1%, or ±1 pF
whichever is greater
£±10%
D.F.
£1.5 x initial requirement
I.R.
³0.25 x initial requirement

*3

Endurance(Life Test)

IEC 384-10 4.15
1000 hrs. at maximum temperature with
1.5 x rated voltage applied
Recovery :6 ~ 24 hrs. (COG)
24 ± 2 hrs. (X7R, Z5U, Y5V)
No visible damage
 COG(1BCG)X7R(2R1)Z5U(2E6)Y5V(2F4)
£GC/C
£±2%, or ± 1pF
whichever is greater
£±20%
£±20%
£±30%
D.F.
£2.0 x initial requirement
£1.5 x initial requirement
I.R.
³0.25 x initial requirement

*4

Humidity Test
(Damp heat,
steady state)

IEC 384-10 4.14 / JIS C5102 9.5
500 hrs. at 40 ± 2oC, 90-95% RH
Recovery :6 ~ 24 hrs. (COG)
24 ± 2 hrs. (X7R, Z5U, Y5V)
No visible damage
 COG(1BCG)X7R(2R1)Z5U(2E6)Y5V(2F4)
£GC/C
£±2%, or±1pF
whichever is greater
£±10%
£±20%
£±30%
D.F.
£2.0 x initial requirement
£1.5 x initial requirement
I.R.
³0.25 x initial requirement
AdhesionIEC 384-10 4.8 / JIS C5102 8.11.2
Capacitors mounted on a substrate, a force of 5N applied perpendicular to the plane of substrate and parallel the line joining the center of terminations for 10 ± 1secs.
No visible damage
    *1 ~ 4 : Class II (X7R, Z5U, Y5V) capacitors shall be made a special pre-conditioning before a test or a sequence of tests under the following conditions : Exposure at 150 ± 10oC for 1 hr, followed by setting the capacitor at room temperature for 24±1hr.
Quantity: